Comparison between constant‐stress and step‐stress accelerated life tests under Time Constraint

By running life tests at higher stress levels than normal operating conditions, accelerated life testing (ALT) quickly yields information on the lifetime distribution of a test unit. The lifetime at the design stress is then estimated through extrapolation using a regression model. In constant‐stress testing, a unit is tested at a fixed stress level until failure or the termination time point of test, whereas step‐stress testing allows the experimenter to gradually increase the stress levels at some prefixed time points during the test. In this work, the optimal k‐level constant‐stress and step‐stress ALTs are compared for the exponential failure data under complete sampling and Type‐I censoring. The objective is to quantify the advantage of using the step‐stress testing relative to the constant‐stress one. Assuming a log‐linear life–stress relationship with the cumulative exposure model for the effect of changing stress in step‐stress testing, the optimal design points are determined under C/D/A‐optimality criteria. The efficiency of step‐stress testing to constant‐stress one is then discussed in terms of the ratio of optimal objective functions based on the information matrix. © 2013 Wiley Periodicals, Inc. Naval Research Logistics 00: 000–000, 2013     

目标识别中的传感器管理方法

基于假设检验的方法,研究了目标识别中的传感器管理方法。分别以用于假设检验问题中的最大后验概率、最小代价函数和最大正确检测概率为目标函数,给出了用于目标识别问题的多传感器管理方法,并针对目标识别问题的特点,对其进行了相应的改进。通过对一定场景的仿真,比较了三种不同方法的识别正确率和平均采样次数,分析了各种方法的特点。     

航空电子总线测试系统的设计与实现

现代航空电子综合化系统通常建立在M IL-STD-1533B多路传输数据总线通信网络基础之上,总线控制器(BC)和各个远程终端(RT)必须满足M IL-STD-1553B规定的各项协议指标要求,才能正确地联网通讯。讨论了某型航空电子总线测试系统的设计与实现,主要探讨了此系统的软、硬件开发,系统组成及其BC和RT有效性测试的主要内容和要求。在实际应用中收到了很好的效果。     

某型枪弹火药性能对内弹道性能影响试验研究

通过对某型枪弹 (如经过技术处理的正常弹、减量弹、加温弹、干燥弹及受潮弹 )初速和最大膛压的测定 ,得出火药的药量、初温及挥发份对内弹道性能 (如膛压、初速 )有较大影响 ,因此 ,必须严格控制弹药的储存条件及装药量。     

步进加速退化试验及其在电子产品可靠性评估中的应用

为快速评估具有高可靠、长寿命特点的电子产品的可靠性，提出了使用步进加速退化试验技术的方法。文中首先给出了步进加速退化的试验方法及基本假设，然后给出了步进退化数据向恒加退化数据的折算方法，在此基础上提出了基于伪失效寿命的步进加速退化可靠性评估算法，最后利用试验数据对该方法进行了验证。该方法与恒加退化试验相比，在保持样本量不变的基础上，可以极大地缩短试验时间，因此，具有更高的效费比。     

Designing a screening experiment for highly reliable products

Within a reasonable life‐testing time, how to improve the reliability of highly reliable products is one of the great challenges to today's manufacturers. By using a resolution III experiment together with degradation test, Tseng, Hamada, and Chiao (1995) presented an interesting case study of improving the reliability of fluorescent lamps. However, in conducting such an experiment, they did not address the problem of how to choose the optimal settings of variables, such as sample size, inspection frequency, and termination time for each run, which are influential to the correct identification of significant factors and the experimental cost. Assuming that the product's degradation paths satisfy Wiener processes, this paper proposes a systematic approach to the aforementioned problem. First, an intuitively appealing identification rule is proposed. Next, under the constraints of a minimum probability of correct decision and a maximum probability of incorrect decision of the proposed identification rule, the optimum test plan (including the determinations of inspection frequency, sample size, and termination time for each run) can be obtained by minimizing the total experimental cost. An example is provided to illustrate the proposed method. © 2002 Wiley Periodicals, Inc. Naval Research Logistics 49: 514–526, 2002; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/nav.10024     

防火涂料性能要求及测试方法探讨

介绍了饰面型防火涂料、电缆防火涂料、钢结构防火涂料以及混凝土防火涂料的理化性能要求及防火性能要求。重点阐述了这些防火涂料防火性能的测试方法。     

退化速率跟踪粒子滤波在剩余使用寿命预测中的应用

毋庸置疑,剩余使用寿命预测对于设备的健康管理越来越重要。近年来粒子滤波方法被越来越多地应用到设备寿命预测技术当中,这是因为粒子滤波方法能更好地解决非线性非高斯系统滤波问题,而且能够获得不确定度信息。但该方法的预测性能却过度依赖于预测模型,并且对于模型参数的初始分布也比较敏感,这在一定程度上限制了粒子滤波预测方法的进一步发展。针对基本粒子滤波预测方法的不足,提出了一种基于退化速率跟踪粒子滤波的通用预测框架,以历史观测数据的退化速率统计规律作为指导来跟踪目标数据的退化速率,实现对粒子滤波预测方法的简化,并将该方法用于轴承和锂离子电池的剩余使用寿命预测,验证了方法的有效性。     

考虑多性能参数的引信弹簧可靠性评估

弹簧作为引信中常用的储能源,是影响引信可靠性的重要零件,而引信失效会形成重大安全隐患。为了准确预估某引信弹簧贮存期间的可靠度变化,提出了一种基于修正Arrhenius模型的多元正态可靠性评估方法。以应力损失率和永久变形率作为性能参数,设计了恒定应力加速退化试验,获取弹簧在120℃、130℃、150℃和160℃下的退化数据,并采用Anderson-Darling统计量验证退化量的最优分布为正态分布。根据修正的Arrhenius方程,得到弹簧在贮存温度下的退化轨迹曲线。基于多元正态分布建立弹簧贮存可靠度模型,分析弹簧贮存期间的可靠度变化特点。通过与其他可靠度模型对比,该模型预估结果更准确,可为引信的视情维修提供依据。     

恒加试验下Pareto部件的可靠性分析

基于定数截尾试验,研究恒加试验下Pareto部件的可靠性分析问题。利用经典方法和Bayes方法,给出了部件参数的极大似然估计、Bayes估计和逆矩估计。验证了极大似然估计和Bayes估计的等价性。结合加速寿命方程,推导出Pareto部件的可靠度、失效率的估计值。最后,通过仿真比较与分析,建立了Pareto部件的可靠性评估方法。